Product Description

The CompreDrive is an electrochemical laboratory-press designed for solid state electrochemistry research under active force and temperature control.

With the CompreDrive, uniaxial forces up to 75 kN (e.g. 663 MPa @ 12mm) can be applied and kept constant on the sample with unprecedented accuracy by the active force regulation system.

Unlike typical active presses the CompreDrive uses an ultra-high resolution servo drive for force regulation instead of a hydraulic system. This allows for high positioning speeds with a minimum step width of <10 nm.

The sample is placed into a specialized measuring cell: the CompreCell. Here, the sample is compressed by hard-metal plungers in an inert, insulating insert. The cell is fully sealed, which allows for measurements under inert gas atmosphere.

Temperature control is achieved by different types of mantles, which are supplied based on your requirements. If only heating is required, an electric heating mantle is sufficient. For heating and cooling, a hollow mantle for use with an external circulating thermostat is available.

The CompreDrive hardware supports a temperature range of -40 - 250 °C.

Product Details
Article No.:
58 x 81 x 170 cm (l x w x h)
Total weight:
180 kg
Force Range:
0.03 - 75 kN
Temperature Range:
-40 °C to 250 °C
Power supply:
115...230V 50...60Hz 10A
The CompreDrive is available in different variants for heating and cooling requirements:
  • 840104: No temperature control, for measurements at ambient temperature.
  • 840105: Heating option. A cell mantle utilizing an electric heater. It allows heating up to 250°C without active cooling.
  • 840106: Heating & Cooling option. A hollow cell mantle that allows active heating & cooling via an external circulating thermostat. The range is limited by the thermostat, with a max. range of -40 - 250 °C.
Compatible measuring cell
Quick Downloads

Introducing the CompreDrive

New experimental horizons in solid state research

For years solid state electrochemistry has been plagued with inconsistent pressure control.
Today, this is finally over! Introducing: The CompreDrive - the first actively pressure- and temperature controlled electrochemical measuring system.
All-solid-state batteries have emerged to solve both the safety concerns as well as the limited energy density of batteries containing classic liquid electrolytes. Since standard battery test equipment was mainly designed for these liquid systems it often remains insufficient for solid state research.
To overcome the common drawbacks of standard test equipment our team has developed the CompreDrive to test the performance of solid and polymeric electrolytes as well as complete (solid-state-)batteries while precisely monitoring and actively adjusting both the mechanical pressure and temperature applied to the sample stack!
Up to 75 kN with 0.5% accuracy
Control and adjust the sample pressure with an unmatched precision and resolution
The CompreDrive allows you to precisely adjust and automatically control the mechanical force applied to your sample within a wide range up to 75kN. The force is automatically regulated by the closed loop control system during (long term) measurements.
The CompreDrive utilizes a high precision servomotor to apply the selected force onto the sample cell's hard-metal plungers. The motor and gear box allow for nanometer scale movements and, thus, for a much finer force control than commonly used hydraulic systems. The applied force is measured directly in line. An closed loop control system drives the motor to keep the selected force constant. This active control can finally eliminate inaccurate force conditions which plagued solid state measurements in the past.
-40 °C to +250 °C
Temperature control and monitoring in line with highest standards
The different available CompreDrive heating units enable adjusting the sample temperature in a range from -40 °C up to +250 °C with a precision of <0.2 °C.
The CompreDrive measuring cells can be equipped with a mantle for either an electrical heating unit or an external circulating thermostat. The mantle can be selected individually for each experiment, giving the maximum flexibility for the researchers specific requirements.
The ability to use an external circulating thermostat allows for cooling the sample down to -40 °C, which is a unique feature for high-pressure solid-state measuring systems.
The temperature is measured very close to the sample with a high-accuracy Pt100 sensor in order to actually control the true temperature of the sample. Given the high thermal-mass of the setup, this is key in achiving high-accuracy temperature-control.
Hover text for highlight
Innovative solid-state cell design
Modular cells allow for out-of-glovebox measurements of sensitive samples
The measuring cells for the CompreDrive are tightly sealed with double-O-ring methods to prevent sample contamination in ambient conditions. Temperature-sensing close to the sample allows for precise and accurate temperature control.
Thanks to the innovative design the measuring cell unit can be loaded with your sample inside of a glovebox while the measurement can be performed outside. This saves valuable glovebox space and avoids the need for additional cable feed-throughs which may cause gas leakage or artifacts during your electrochemical measurement. In addition, this concept avoids heating of your glovebox atmosphere. In case of testing an all-solid-state battery, you can easily build up the battery layer by layer, increasing the level of flexibility.
Materials and customization
System design with high-performance materials while keeping it customizable
The CompreDrive and its measuring cells keep only selected materials in contact with your sample but still allow for customization.
All force-bearing components are fully machined from hard-metal to reduce deformations. Electrical insulation is achieved by employing an Al2O3 ceramic or PEEK insulation insert. All materials are machined to the highest quality and precision standards.
Since each researcher needs to enjoy high-quality and reliable experiments but also has individual ideas and requirements, our philosophy is to find a setup configuration that fulfill your needs 100%. If our standard setup does not satisfy this, please get in touch so we can find a solution that does!
Benefit from automation
Embed the pressure & temperature control directly into your measurement
The CompreDrive can automatically run combined pressure and temperature procedures from its CompreDriveControl software. Its abilities can be embedded directly into measuring procedures of many potentiostat and EIS analyzer manufacturers.
The CompreDrive offers various interfaces, either in hardware through digital triggers or through a REST service provided by the CompreDriveControl software. The hardware triggers can be used to advance the pre-programmed procedure to a different pressure/temperature after e.g. an EIS spectrum was measured. They can then signal back to the analyzer that the new setpoint was reached. The REST service allows directly getting and setting the CompreDrives parameters as well as adjusting the setpoint without pre-programming a procedure, thus allowing for actual data transfer to the analyzer software.
Reproducible sample preparation
Use the CompreDrive for sample preparation, not only for testing
In addition to its abilities in sample characterization the CompreDrive can also be used to prepare samples more reproducible than what was possible with classical laboratory presses. The CompreDriveControl software allows for generating standardized pressure and temperature dependend sample preparation procedures.
Solid-state sample preparation often involves the fabrication of well-defined pellets as well as optional (low temperature-)sintering steps. This usually involved hand-operated hydraulic presses with inaccurate force and time control. The CompreDrive can be used to prepare samples using well-defined pressure and temperature steps, which allows for an actual optimization of preparation procedures. This can lead to more reproducible samples and experimental results.
Modern user-interface
Control your CompreDrive comfortably using a comprehensive software package!
The CompreDriveControl software connects with both the CompreDrive as well as a temperature controller. It then offers all functionality required for manual control as well as automated measurements.
The manual control mode allows you to set the CompreDrive to a specific force and temperature setpoint. You can inspect the force and temperature as a function of time in a customizable plot and log the full data to a file. In manual control the CompreDriveControl software can also accept setpoints supplied via a REST API with a simple http interface. The same interface can also be used for reading the current force and temperature values as well as for triggering. For static measurements the closed loop control system can be deactivated after a manual setpoint is reached.
For automatic measurements CompreDriveControl offers a convenient procedure builder. Here you can define a series of setpoints that will be applied one after another. The running procedure can be synchronized with an electrochemical device via hardware or software (REST) triggers. This allows for e.g. triggering a measurement when the force and temperature are stable, and move to the next step once the measurement is complete. The measured force and temperature data can be logged to a file.
Cookies are used to store information like your shopping cart. We do not use any tracking cookies. You can decline the storing of cookies, which are then subsequently deleted once you exit the browser. In this case, you will loose the stored information, e.g. your cart.